October update 1

During the last week I have rebuilt and fitted the twin tone horns and have been slowly reconnecting the front wiring loom to the push button light\wiper switch unit, new fuse box and relays etc. this seems to be going well so far and I intend to press on and fit the small inner light, door switch loom and then the main rear wiring loom over the next week or so.

I am looking forward to receiving a rear wing drain tube from Bert3 in Belgium shortly, he was breaking a May 62 T34 which has exactly the correct sort of drain tube fitted only to the early cars, the one on the right is the earlier type and the body work has a narrower outlet in the bottom of the rear wing to accommodate it.

September update 4

I have continued to concentrate on the front of the car and have now finished the majority of the front boot area, other than securing the spare wheel well and adjusting the front bumper and boot lid.

The other major task remaining is to get the headlights to fit. The correct headlamp to body work seals are proving too thick to enable the top of the headlamp rim to locate on the headlight bowl hook. I have adjusted the hook as best as possible and removed excess paint from the rear, as well as checking that the headlight rim retainer springs are not in the way but so far no joy. My approach is leave them until next week and have a beer!

September update 3

I have refitted the fog lights after putting the new front wiring loom in place etc. Luckily I had one original remaining fog light to body seal (dark grey in colour). To replicate them I took some NOS T14 inner headlight seals (light grey, like the headlight to body seals) that go around the lense and cut of the outer edge of them and then adjusted them to the correct length and super glued them together to make great replacement seals.

I have also recreated the front bonnet drain pipe. To do this I took a T14 front bonnet corner drain and cut it in 2 as in the photo. I then purchased some tubing with the correct internal diameter to accommodate the end of the corner drain with the 90 degree bend. Once this was glued in place I located this in the hole in the front slam panel and then made an cross shaped incision in the top of the rubber horn knickers used for covering pre 65 model T34s, ensuring that the pipe went far enough into the knickers so that the water drained externally rather than accumulating inside the knickers or entering the car.

To do this for 65 and later model cars it is advisable to use 2 T14 front bonnet corner drains, using one at the top and one at the bottom where it will exit through the horn hole blanking plate (As horns fitted to bumpers).

If you are really careful with your craft knife you can also take the part from an old pair of the rubber horn knickers that goes into the horn hole and cut an extra slot into the internal lip to accommodate the blanking plate as well as this rubber is no longer available. did this on my 65 back in 1992 and it is still working OK.

September update 2

I have concentrated on installing the front wiring loom today. the reproduction loom made by Autosparks is excellent and they built in all the repairs to the loom that were needed to bring it back to original spec. One thing I left as it was on the original loom was the wire from the horn relay to the fuse box. This was black with a yellow stripe, rather than green in the wiring diagram.

Next on my plan is to press on and finish everything in the front bonnet area and then move to the installation of the main loom and completion of the rear boot area.

When trial fitting the lower dash pad as mentioned in a previous posting, I found that as expected the later post may 62 padded dash pad that I bought won't fit my pre may 62 dash without alteration. You can see why if you look at the photo of my dash versus the dash of Paul Colberts car (thanks Paul, photo lifted from your site).

In May 62 the steering column was raised 20mm and they did this by cutting out a section of the dash board. The later padded dashes therefore won't fit as they are not recessed to accommodate the area over the top of the steering column that was removed and existed on the first production cars.

September update 1

I have fitted the brake fluid reservoir and line to the master cylinder and refitted the petrol tank and breather pipes. Also now installed in the front boot is the tank top liner,flip up tray for the spare wheel and the paint colour code sticker. once I have the spare wheel well back from the body shop then that can be fitted as well. Photo shows the area before some final paint touching up was completed.

At the rear the air control flap in the engine bay and cardboard intake pipe is in place along with the rubber belows and correct clamps. I had a NOS set of bellows - went to fit them and my fingers went straight through the rubber whilst manipulating them into place - luckily as usual I had a good used one in the cupboard and that has now been fitted.

the rear and side badges are in place, the side ones look to be a bit of an issue as the Karmann script looks out of line - not going to worry at this stage as I shall accumulate any issue and take the car to the body shop at the end of the fit up for final sorting. This is a problem of my making as I drilled the holes.

I offered up the lower dash pad to see if it would fit OK - early 62 cars had a slightly different lower dash area, cars from May 62 had the steering column raised 20mm, this altered the dash shape and the lower pad shape. So looks like I will need to be brave and cut the rear of my later lower pad to make it fit.

I have been fitting the various heater pipes inside the car, I am sure I took photos of where each of them went and I know roughly their location under the rear seats and in the inner rear wing to rear screen outlet but am no longer sure which goes where. Without the photos it will be a process of elimination. one pipe needs sections replacing and I have the correct diameter tubing to do this, a task for the weekend.

August progress 1

Since getting the body back time has unfortunately been in shorter supply than anticipated but some progress has been made.

All bolts for the chassis are loosely in place with the exception of one large frame head bolt which refused to go in. I will try again this weekend and if needed use a tap to clear the thread in the captive bolt, nothing is being tightened down until that is in place.

Front and rear boots have now been fitted, some minor adjustment is needed to get the correct gaps but they are safely installed on the car. I will leave the doors off for the time being as space is tight and this should prevent damage to them.

The seats are loosely installed as well to keep them safe from the marauding dog.

A few minor problems have surfaced, none paint related, the spare wheel restraint bar (best way I can describe it) has been welded to the inner wing in the wrong place. this stops the jack being stored in the front boot and lets the spare wheel move around too much. the paint shop say they can help sort this for me. Also I thought I had sourced a missing early rear air intake to rear wing drain pipe but I can't find one - if anyone has a correct driver side one then let me know - it is the shorter flat ended one in the photo and has a narrow end, this prevents the later ones being used.

When little issues like this come up I turn my attention to simpler tasks like small trim item fitting, this is good as it also gives the illusion of progress as well. Even here things don't always go as well as expected - the drivers side sill trim clips are not holding the trim in place as well as they should and I will have to think about a remedy for this.

Anyway, reasonable progress so far and I will look to do more at the weekend.

Back to black and back home

The bodyshop delivered the bodyshell back home this afternoon - it looks absolutely fantastic. the doors and bonnets will follow in the next few days.

They managed to weld up the two horn wire holes in the front panel that I had missed - these were only on cars from 65 model onwards once the horns became externally mounted.

Anyway I have an initial plan of action for the weekend which will be;

• Fit the bumpers and get them out of harms way and give protection to the car



• Bolt the chassis down



• Fit the steering column



• Fit all locks and latches where ever possible

I am not going to rush after all this time but will move on at a good pace.

Its in the spray booth

The 62 has had its' final prep finished and is now in the spray booth. It will be sprayed on Monday and hopefully home by next weekend. It's come a long way from a car that was de-registered and classified as scrap in South Africa which again was an accurate description. The final stages are close and re-assembly will be a pleasure.

Front Axle - here we go again

Well the front axle and chassis have been completed for a couple of years now. I decided to replace the 2 smaller rubber bumps stops with new ones that I bought and during the process also replaced the track rod end boots that had perished since fitting. Not good as they were new stock, not NOS.
Whilst doing all this I noticed that the rubber boots on the 2 upper ball joints were also cracking. These were NOS in the box but a good number of years old. I dug out the ball joints that I took of the car and luckily the boots on them were perfect, strange as I think one was an original item.
I called the body shop today, they have finished rubbing down and perfecting and the car goes into the spray booth today for final prep coat and hopefully top coats next week.

Trim items

Having completed the bumpers I am now digging around in my boxes of trim to see where some work is needed before re-assembly.

I needed a new rear boot rubber, these are not available with the original moulded lower corners. Digging around in my cupboard of wonder produced a nearly complete rubber, all present except for the piece that goes around the are for the oil filler. Lee Hedges gave me bits of an old rubber when I was over visiting him and luckily I was able to salvage the missing piece from that.

It will all need a good clean up and gluing here and there but will look better, even if slightly worn, that the reproduction ones.

At the same time I dug out some old trims for the A & B posts, these fell apart when I took them off the car, luckily I have enough of the 3 I found to be able to recreate some new ones.

Bumpers complete

I have now coated the insides of the bumper blades with hammerite paint and sprayed them on top of this in a silver colour, similar to original to finish them off. They are now fully assembled and have been wrapped up to prevent damage before fitting in the near future.